Archive for December, 2016

Characteristics of co – closed closed precision punch machine

1. Superior plan, high-rigidity three-stage punch body, 4 2 times the nominal force of the pre-tightening rod, locking by the high-pressure oil lock, stable shape, high precision control of the bottom dead center precision, and as long as the custody Department of hydraulic pressure can play card mode. 2. 4 points support the crankshaft, the support point near to avoid the crankshaft force deformation, and precision can be adhered to, the fulcrum and connecting rod are applied to import heavy duty fine rolling bearings, the gap is minimal, argue that force is very small, Block not only the death of the shock and greatly reduce the debate that fever, reduce deformation energy consumption.

3. Equalization of audio equipment, set aside the weight of the weight of the audio balance display can be low consumption back and forth movement produced Hongyuan inertia angle drill machine, vibration is minimal, 4. Slide guide system, take the above large double guide column, the top four circular static pressure guide column, large guide column can suck rod movement lateral force and can withstand a larger mold upward preference load, 4 round static guide column High precision, good orientation, strong anti-bias technology and can be symmetrical row of stamping produced by lateral anti-induced force. 5. Stress cycle smooth furnishings, after a strong motor smooth all the movement of machine parts, to avoid wear. In order to avoid heat on the impact of product quality, configuration cooling oil circulation equipment. 6. Preferred axis plan, adopt high-strength alloy steel, heat treatment hydraulic busbar cutter, grinding, far more than the general crankshaft plan, CNC punch presses can withstand greater technical output and stable shape. 7. Rib hydraulic locking device beveling machine, the application of high-pressure oil lock, remove the mold-rib clearance, guarantee the accuracy of movement back and forth.

Co-forging precision forging press, spinning Spinning

Co-forging precision forging press, spinning Spinning is the common rotation of the slab and mandrel drilling machine manufacturers, the pressure from the roll wheel and the pressure, so that slabs close to the local deformation of the core point by point of the stamping process. Spinning principle Spinning can produce a variety of axisymmetric rotating parts cnc plate drilling machine, such as loudspeakers ﹑ ﹑ ﹑ pressure vessel head closure gongs; can also be used for closing the cylinder ﹑ ﹑ tube forming angle steel open. Spinning is characterized by: small deformation force can be formed with a large workpiece; use of equipment is relatively simple, small and medium size sheet metal parts can be used ordinary lathe spinning; mold is simple, only a core mold, material requirements low.

Spinning applies to small batch production, because it can only rotate parts of the body, the limitations of large, low productivity. Spinning can be used special machinery, the use of copy spinning and digital control spinning. Spinning at the same time the thickness of the thinning process known as thinning spinning, also known as strong spinning, used for processing cone-shaped pieces of thin-walled, etc., can also be used to spin a large diameter deep Tube, and then cut open after the plate.

Co-forging precision punch use IPM precision punching equipment

Co-forging precision punch use IPM precision punching equipment is widely used in home appliance manufacturing, automobile manufacturing, electrical and electronic manufacturing, medical equipment, lighting, connectors, terminals, shrapnel and all kinds of hardware products. Using high-grade, high-strength cast iron to create. To ensure the accuracy of the product drilling equipment companies, we are applying for a patent, I believe in the near future, we can artificially limit the maximum natural mechanical wear and tear.

IPM PRECISION PUNCH As the manufacturer of punch press Angle Steel Punching Machine, we aim at improving the stamping technology capacity, customer first and sincere service as our business tenet. We are adhering to the meticulous and meticulous work requirements of fine workmanship, strict quality and continuous improvement. Each IPM machine cnc drill machine. To innovation, sincerity of the business philosophy, service to our customers.

professional punch manufacturer sieve plate machine

Co-forging precision presses, high-quality presses, Foshan Punch IPM insists on the quality policy of ‘quality and service’ automatic punching machine, continuously improves the quality consciousness and quality level of the whole staff, confirms the quality target and the principle of compliance, and ensures the advanced position and reliability of IPM precision punching machine in the market competition busbar machine. The company produces high-quality presses, low-cost presses, IPM – Foshan punch is your trusted professional punch manufacturer sieve plate machine, please call to discuss: info@ipmmc.com.

On the domestic punch technology to be improved 10 years in the world

On the domestic punch technology to be improved 10 years in the world is still in the bubble burst after the false alarm, our country has won two consecutive ‘world first’. First, the car yield reached 13.7 million cnc drill, the ‘world first’ is usually considered to be the symbol of access to industrial countries. Second, China’s punch industry output value of 401 hydraulic press.4 billion yuan, the first time the world’s first big punch into the country. The car went down the assembly line of the factory. Those used to polish the parts, assembly of various colors of the car is a great machine, is the punch. Punch also known as machine tools.

Marx once said that the machine tool is the starting point of the eighteenth industrial revolution. The industry has this argument, saying that China’s manufacturing is ‘polished goods’, made in Germany or Japan, is known as ‘manufacturing plant’. The implication, the level of industrialization progress and occlusion, in the punch of this industry ‘machine’ production capacity Beam Sawing Machine, who holds the bull? 2002 so far, China’s first 10 years of light for the first punch and the largest importer of large countries, punch into the super-business there are billions of dollars. This means that, despite the large capacity of our industry, but in fact or ‘armed themselves’. Today, China’s ‘world polishing factory’ has been to upgrade the final restructuring of the teeth, not only to be able to polish the goods, but also must be able to ‘manufacturing plant’. The first demand to climb the ‘threshold’, is the punch.

Talking about the Development Trend of Press In the severe economic environment

Talking about the Development Trend of Press In the severe economic environment, non-cutting forming is a powerful means to win the competition and distance between enterprises and competitors, and environmental protection is the theme of the 21st century, as environmental protection processing methods will be the main direction of development. High-precision, high-value form-free forming is essential for cutting angle iron drill. In order to achieve these requirements, it is necessary to understand the overall process from material to finished product. Punch on one of the important technical elements. Punch the basic characteristics and developed in recent years applicable to a variety of forming technology, high-precision multi-function punch direction of development. There are two main characteristics of a punch, one is rigid, which includes the longitudinal stiffness of the slider and table arch and the elastic elongation of the frame; and lateral stiffness under the influence of the eccentric load of the horizontal displacement of the slider. The second is the movement of the slider characteristics, including the vertical, parallelism, straightness, etc., have a great impact on the accuracy of the product.

The accuracy of the product is not only with the punch, and materials, molds, lubrication and so on custom processing machine, can not only consider a certain factor. The accuracy of the thickness direction of the product is related to the longitudinal rigidity, while the deviation, bending or parallelism is related to the transverse rigidity and the characteristics of the motion profile. So to improve these characteristics, product accuracy can be improved, die life extension, production stability can be improved. Universal punch high rigidity, high performance: the original general-purpose machine C-shaped punch is also the pursuit of high-precision, high performance, which developed an integrated gantry punch; with AIDA connecting rod drive mechanism and near the bottom dead center speed Slow and SPM unaffected rod presses. The connecting rod presses the two eccentric connecting rods between the drive gear and the crankshaft hydraulic punching machine. When the driving gear rotates, the crankshaft does not move at a constant speed due to the change of the connection angle of the connecting rod. Unlike the other link mechanisms, the link mechanism has a small number of connection points of the pressure receiving portion and a small integrated gap. As shown in Fig. 8, the connecting rod mechanism has a higher torque capacity than the toggle mechanism, and can be formed at a higher dead center position.

IPM pneumatic punch, the mold should be safe operation

IPM pneumatic punch, the mold should be safe operation First, the work before the pneumatic punch press the power button to open the first off, not a sudden start, stop 5 minutes check the content: 1), check the punch health iron Marking Machines, table clean no debris. Hydraulic press, pneumatic presses, hydraulic presses, C-hydraulic machine 2), check the machine lubrication system, mechanical system is normal shearing machine. Hydraulic press, pneumatic presses, hydraulic presses, C-hydraulic machine 3), check the clutch, the brake is flexible and easy to use, foot pedals, rods, pressure plate, screws and the operation of the device without loosening.

Hydraulic press, pneumatic presses, hydraulic presses, C-hydraulic machine 4), check whether the mold head fracture, die is bang bite, limit column is loose. Hydraulic press, pneumatic presses, hydraulic presses, C-hydraulic machine 5), clean mold chest. Hydraulic press, pneumatic presses, hydraulic presses, C-hydraulic machine 6), check whether the stamping die and the pressure plate is installed firmly marking machine, punch whether the batter situation. Hydraulic press, pneumatic presses, hydraulic presses, C-hydraulic machine 7), check the electrical grounding line intact, tubing smooth without clogging, no rupture. Hydraulic press, pneumatic presses, hydraulic presses, C-hydraulic machine

The future market demand of punch press and the development direction of punch press manufacturer

The future market demand of punch press and the development direction of punch press manufacturer China’s largest punch as one of the countries machinery manufacturing, but most of our factories are produced by the equipment are some no-name products, technical content and other brands of punch equipment compared to a relatively large difference, not in the same level , Fortunately, as China’s technology matures, the gold content of the equipment is also getting higher and higher, such as China’s Taiwan region, such as punch Jinfeng punch, in terms of performance and price has been an international leader, with some of the traditional Punch the gap between enterprises is also growing.

 

Some middle and low-end enterprises in order to survive in the fierce competition which should be more equipment to upgrade the processing Steel Punching, the latter part of the development of enterprises and equipment needs not only by a certain aspect (such as price) decision, more enterprises Procurement of equipment will be conducted when an integrated study, cost-effective products is the focus of future business direction of choice. For precision punching production enterprises, to enhance their product accuracy and equipment life and the quality of products stamping out is the focus of future development steel straightening machine. The ability to grasp the needs of market customers to carry out product sales Companies specializing in the provision of high-quality precision punching equipment bus bar bender, products widely used in the manufacturing industry, machinery industry, and so on a number of areas. High-quality products and perfect after-sales service is fundamental to our survival, the punch press recently in a series of international press exhibition and the corresponding press appraisal activities have gained a good reputation and market influence.

Changes in the market demand for change in customer interest points are also changes in time, the company believes that we provide the equipment can be targeted to meet the needs of all sectors of the customer. We will provide the latest and highest development technology; accurate and precise production technology; accurate and rapid sales? Services, to improve the world’s customers the production capacity and production efficiency and make unremitting efforts.

What punching process can be efficient production

Precision punching press is a press. In the national production, the stamping process because of the traditional mechanical processing for saving materials and energy, high efficiency, low technical requirements for the operator and through a variety of mold applications can be made by machining products can not achieve these advantages cnc drilling machine for sale, and thus It is used more and more widely boring drilling machine. Precision punching, punching tonnage: 30 tons -65 tons. High-strength cast iron frame, the stress elimination, to ensure long-term precision. Three-round guide column slider structure, to minimize the dynamic friction, with forced lubrication, so that heat to a minimum. Dynamic balance system to balance the crankshaft, slider at high speed vibration, control the bottom dead center precision.

Precision Punch frequency control can be started at zero speed and in accordance with the needs of users to smooth acceleration plate beveling machine, and its acceleration curve can also be selected. CNC punch through the start frequency of the motor or the mechanical part of the connected shaft or gear will produce severe vibration. This vibration will further aggravate the mechanical wear and loss, reduce the mechanical parts and motor life. In addition, the frequency conversion start can also be applied to similar filling line to prevent the bottle upside down or damage.

Precision press photoelectric protection device

Precision punch press photoelectric protection device, photoelectric protection device, also known as photoelectric handguards, safety light curtain angle iron shear, is a non-mandatory precision punch press matching device, mainly for precision punching dangerous processing area security protection, protection of stamping processing personnel production personnel Safety. With stamping customers on the processing of production safety requirements are getting higher and higher, with the resulting change is more and more customers choose to install a photoelectric protection for the press, high-speed press after the installation of photoelectric protection device in the punch slip Block down the stamping to play a protective role, once the detection of hazardous objects in the processing area, it can automatically control punch press downtime, thus fundamentally ensuring the life of the punch operator safety. In this case, The photoelectricity protection device of precision press consists of light emitter, light receiver, steel tube support, signal cable and controller. The controller consists of intermediate relay bevel tools, stop button and return solenoid valve.

The coil of intermediate relay is connected to the output of PLC controller, The normally open contact of the intermediate relay is connected in series with the return solenoid valve. The stop button is connected in parallel with the photoelectric protection device and connected to the input end of the PLC controller. The light emitted from the light emitter is directed to the light receiving device to form a protective light curtain. When the light curtain is blocked, the receiver generates a shading signal, through the signal cable to the controller, the controller will process this signal to produce a control signal, control precision punch press control circuit alarm device to achieve punch press parking Or safety alarm. When the precision punch press photoelectric protection device detects the dangerous area has the object, its normally opens the contact to be closed, is equal to the return position solenoid valve does not work; When the photoelectricity protection device detects the dangerous region to have the object in the precision press slide, the photoelectricity protection device relay, When the stop button is pressed, the input of the PLC controller is turned on, all the solenoid valves of the precision punching machine are de-energized and the press is stopped plate beveling machine.